锤式破碎机 pc-600x600
- 类型：塑料粉（破）碎机
- 价格：18600元
- 设备说明：锤破制砂机供应厂家锤破制砂机锤破破碎机
锤式破碎机的保养方法有哪些
1、定期检查机器内部部件的磨损情况要定期检查机器内部部件的磨损情况，如中心入料管、锥帽、叶轮上、下流道衬板、圆周护板、鄂板的磨损程度，磨损较严重的要及时进行修补或更换，同时更换部件的重量、型号和尺寸等，一定都要按原来的部件参数进行更换。
2、做好润滑工作要经常注意并及时做好摩擦面的润滑工作，且所采用的润滑脂应根据使用的地点、气温条件而定，一般情况下采用钙基、钠基和钙钠基润滑脂;加入润滑脂时应先用洁净的或煤油清洗滚柱轴承的滚道，然后再加入，加入轴承座内的润滑脂应为其空间容积的50%左右，锤破制砂机生产厂家，而且每3~6个月更换一次，这样既确保了机器的正常运转又延长了使用寿命。
3、保持设备的清洁要经常保持设备的清洁，做到无积灰、无油污、不漏油、不漏水、不漏电、不漏灰，更要注意灰尘等杂物不得进入润滑系统和润滑部位，锤破制砂机现货销售，因为这些杂物不仅会破坏润滑油膜，而且会使设备失去润滑而增加磨损，缩短设备的使用寿命;尤其要注意对轴承的定期清洗，破碎机在作2000小时后，打开主轴总成对轴承进行清洗，一般工作7200小时后要更换新轴承。
What are the maintenance methods for hammer crushers
1. Regularly inspect the wear of internal components of the machine, such as the wear degree of the central feeding tube, cone cap, impeller upper and lower channel lining plates, circumferential guard plates, and jaw plates. Those with severe wear should be repaired or replaced in a timely manner. At the same time, the weight, model, and size of the replaced components must be replaced according to the original component parameters.
2. Regular attention should be paid to and timely lubrication of the friction surface when performing lubrication work, and the lubricating grease used should be determined according to the location of use and temperature conditions. Generally, calcium based, sodium based, and calcium sodium based lubricating greases are used; When adding lubricating grease, the raceway of the roller bearing should be cleaned with clean or kerosene first, and then added. The lubricating grease added to the bearing seat should be about 50% of its spatial volume. The manufacturer of the hammer sand making machine should replace it every 3-6 months, which ensures the normal operation of the machine and extends its service life.
3. To keep the equipment clean, it is necessary to regularly maintain its cleanliness, ensuring that there is no accumulation of dust, oil, oil, water, electricity, or dust. It is also important to note that dust and other debris should not enter the lubrication system and lubrication parts. Hammer sand making machines are sold in stock because these debris not only damage the lubricating oil film, but also cause the equipment to lose lubrication and increase wear, shortening its service life; Special attention should be paid to regular cleaning of bearings. After 2000 hours of operation, the crusher should open the main shaft assembly to clean the bearings. Generally, new bearings should be replaced after 7200 hours of operation.【详情】
锤式粉碎机 pc-600x400
- 类型：塑料粉（破）碎机
- 价格：14500元
- 设备说明：木材，青石破碎机_大型青石锤破机_青石破碎机厂家
青石是各种石材中环保的石材，因取材方便，具有耐磨、耐风化、无辐射等特点，破碎后广泛用于建筑行业中。青石破碎生产线每小时可生产30-3000吨物料。青石破碎生产线设备有：给料设备、破碎设备、筛分设备、输送设备、制砂设备、洗砂设备、除尘设备组成。
青石破碎机是青石破碎生产线的设备之一。主要作用是：将从山上开采的大块青石料进行破碎，破碎至25-20mm以下成品料，破碎+整形，二合一设备。
青石破碎机工作原理：电动机经三角带、大带轮带动转子高速旋转；待破碎物料由喂料设备经入料口送入破碎腔、高速旋转的转子带动锤头对物料进行次打击；获得动能后的物料高速撞向反击板得到二次破碎；碰撞反弹后或遭锤头再次打击或与其它物料相互碰撞。物料在碰撞的过程中逐渐向破碎腔下部的活动反击板移动，当物料粒度小于锤头与活动反击板之间的间隙时，在自重和其它物料的压挤下脱离破碎腔,从而结束一个完整的破碎过程。排出后的物料由筛选设备筛选后,部分大于选用标准的物料,需运送破碎机进行二次破碎。
青石碎石机是青石制砂生产线中的设备。主要用于：将破碎设备处理后的半成品料进行加工处理，获得用于盖房的大沙。
青石碎石机工作原理：青石碎石机主要由机体、破碎板、上转子、下转子、摆锤、旋转驱动装置、筛板等组成，该机在工作过程中两个转子相对运转，进入破碎腔的物料由个转子上的锤头进行打击破碎并获得的动能后撞向第二个转子，由于第二个转子与物料飞来的方向相反，此时第二个转子对物料的打击速度等于两个速度的叠加，物料经如此多次的循环打击而破碎后经篦条的缝隙排出。破碎原料(石灰岩、青石、砾石、煤矸石、煤、片麻岩等)通过ZG振动给料机均匀地喂入PCZ重型锤式破碎机初步破碎，经粗碎后的成品通过皮带输送机输送至PC锤式破碎机破进一步破碎，二次破碎后的石料通过皮带输送机输送至青石破碎机再次破碎，再次破碎整形处理的石料通过皮带输送机输送至YK振动筛筛分出不同规格的石子，满足客户粒度要求的石子通过皮带输送机输送至成品料堆，不合格的石子通过皮带输送机重新返回至青石破碎机再次破碎，形成闭路多次循环完成。
Qingshi is an environmentally friendly stone among various types of stones. Due to its convenient material selection, it has the characteristics of wear resistance, weathering resistance, and non radiation. After crushing, it is widely used in the construction industry. The bluestone crushing production line can produce 30-3000 tons of materials per hour. The equipment for the bluestone crushing production line consists of feeding equipment, crushing equipment, screening equipment, conveying equipment, sand making equipment, sand washing equipment, and dust removal equipment.
The bluestone crusher is one of the equipment in the bluestone crushing production line. The main function is to crush large pieces of green stone extracted from the mountain, crushing them to finished materials below 25-20mm, and using a two in one equipment for crushing and shaping.
Working principle of bluestone crusher: The motor drives the rotor to rotate at high speed through a V-belt and a large pulley; The material to be crushed is fed into the crushing chamber through the feeding port by the feeding equipment, and the high-speed rotating rotor drives the hammer to strike the material; After obtaining kinetic energy, the material collides with the counterattack plate at high speed and undergoes secondary crushing; After collision and rebound, or being hit again by a hammer or colliding with other materials. During the collision process, the material gradually moves towards the movable impact plate at the bottom of the crushing chamber. When the particle size of the material is smaller than the gap between the hammer head and the movable impact plate, it separates from the crushing chamber under its own weight and the pressure of other materials, thus ending a complete crushing process. After the discharged materials are screened by the screening equipment, some of the materials that are larger than the selected standards need to be transported to the crusher for secondary crushing.
The bluestone crusher is an equipment in the bluestone sand production line. Mainly used for processing semi-finished materials processed by crushing equipment to obtain large sand for building.
Working principle of bluestone crusher: The bluestone crusher is mainly composed of a body, a crushing plate, an upper rotor, a lower rotor, a pendulum, a rotary drive device, a sieve plate, etc. During the operation of the machine, the two rotors rotate relative to each other. The material entering the crushing chamber is crushed by the hammer head on each rotor and the kinetic energy obtained is then collided with the second rotor. Since the direction of the second rotor is opposite to the direction of the material flying, the impact speed of the second rotor on the material is equal to the superposition of the two speeds. After so many cycles of impact, the material is crushed and discharged through the gap of the grate. Crushed raw materials (limestone, bluestone, gravel, coal gangue, coal, gneiss, etc.) are uniformly fed into the PCZ heavy-duty hammer crusher through a ZG vibrating feeder for initial crushing. The roughly crushed finished product is transported to the PC hammer crusher for further crushing through a belt conveyor. The stone material after secondary crushing is transported to the bluestone crusher for further crushing through a belt conveyor. The stone material after further crushing and shaping is transported to the YK vibrating screen for screening different specifications of stones through a belt conveyor. The stones that meet the customer's particle size requirements are transported to the finished material pile through a belt conveyor, and the unqualified stones are returned to the bluestone crusher for further crushing through a belt conveyor, forming a closed circuit for multiple cycles to complete.【详情】
锤式破碎机 pc-520x310
- 类型：塑料粉（破）碎机
- 价格：8600元
- 设备说明：锤式破碎机|锤式粉碎机|锤破机-河南瑞朗机械
锤式破碎机的优点是：破碎比大（一般为10-25，高者达50），生产能力高，产品均匀，过粉现象少，单位产品能耗低，结构简单，设备质量轻，操作维护容易等。锤式破碎机系列产品适用于破碎各种中等硬度和脆性物料，如石灰石、煤、盐、白亚、石膏、明矾、砖、瓦、煤矸石等。被破碎物料的抗压强度不超过150兆帕。该机主要用于水泥、选煤、发电、建材及复合肥等行业，它可以把大小不同的原料破碎成均匀颗粒，以利于下道工序加工，机械结构可靠，生产效率高，适用性好。
Hammer crusher | Hammer crusher | Hammer crusher - Henan Ruilang Machinery
The advantages of a hammer crusher are: a large crushing ratio (usually 10-25, with the highest reaching 50), high production capacity, uniform product quality, less powder passing phenomenon, low energy consumption per unit product, simple structure, light equipment weight, easy operation and maintenance, etc. The hammer crusher series products are suitable for crushing various medium hardness and brittle materials, such as limestone, coal, salt, Baiya, gypsum, alum, bricks, tiles, coal gangue, etc. The compressive strength of the crushed material shall not exceed 150 megapascals. This machine is mainly used in industries such as cement, coal preparation, power generation, building materials, and compound fertilizers. It can crush raw materials of different sizes into uniform particles for the next processing step. The mechanical structure is reliable, the production efficiency is high, and the applicability is good.【详情】
锤式破碎机 pc-450x240
- 类型：塑料粉（破）碎机
- 价格：6800元
- 设备说明：锤式破碎机_锤式破碎机价格_破碎设备产品库-河南瑞朗机械
锤式破碎机是由锤式破碎机箱体、转子、锤头、反击衬板、筛板等组成。主要用于在水泥，化工，电力，冶金等工业部门破碎中等硬度的物料。
锤式破碎机由上壳体、下壳体、传动部件、筛板部件等组成。
锤式破碎机适用于破碎抗压强度180MPa以下的石灰石、煤矸石、石膏、页岩等各类中硬脆性物料的粗、中、细碎作业。锤式破碎机是直接将最大粒度为600-1800毫米的物料破碎至25或25毫米以下的一段破碎用破碎机。
锤式破碎机适用于在水泥、化工、电力、冶金等工业部门破碎中等硬度的物料，如石灰石、炉渣、焦碳、煤等物料的中碎和细碎作业。单段锤式破碎机为重锤式破碎机，又叫复合锤式破碎机，主要用于石灰石的破碎作业，大型单段锤式破碎机可以将1米直径的石灰岩直接破碎到20mm左右，具有强大的破碎能力。单段锤式破碎机在水泥行业具有大量的应用。
锤式破碎机主要是靠冲击能来完成破碎物料作业的。锤式破碎机工作时，电机带动转子作高速旋转，物料均匀的进入破碎机腔中，高速回转的锤头冲击、剪切撕裂物料致物料被破碎，同时，物料自身的重力作用使物料从高速旋转的锤头冲向架体内挡板、筛条，在转子下部，设有筛板、粉碎物料中小于筛孔尺寸的粒级通过筛板排出，大于筛孔尺寸的物料阻留在筛板上继续受到锤子的打击和研磨，直到破碎至所需出料粒度最后通过筛板排出机外。
Hammer crusher, Hammer crusher price, Crushing equipment product library - Henan Ruilang Machinery
A hammer crusher is composed of a hammer crusher housing, rotor, hammer head, impact lining plate, sieve plate, etc. Mainly used for crushing medium hardness materials in industrial sectors such as cement, chemical, power, metallurgy, etc.
The hammer crusher consists of an upper shell, a lower shell, transmission components, sieve plate components, etc.
The hammer crusher is suitable for crushing various types of medium hard and brittle materials such as limestone, coal gangue, gypsum, shale, etc. with compressive strength below 180MPa in coarse, medium, and fine crushing operations. A hammer crusher is a crushing machine used to directly crush materials with a maximum particle size of 600-1800 millimeters to 25 or less millimeters.
Hammer crushers are suitable for crushing medium hardness materials such as limestone, slag, coke, coal, etc. in industrial sectors such as cement, chemical, power, metallurgy, etc. The single-stage hammer crusher is a heavy hammer crusher, also known as a composite hammer crusher, mainly used for limestone crushing operations. Large single-stage hammer crushers can directly crush limestone with a diameter of 1 meter to about 20mm, with strong crushing capacity. Single stage hammer crushers have a wide range of applications in the cement industry.
Hammer crushers mainly rely on impact energy to complete material crushing operations. When the hammer crusher is in operation, the motor drives the rotor to rotate at high speed, and the material uniformly enters the crusher chamber. The high-speed rotating hammer head impacts, shears and tears the material, causing it to be crushed. At the same time, the gravity of the material itself causes the material to rush from the high-speed rotating hammer head to the baffle and screen strip inside the frame. At the lower part of the rotor, there is a sieve plate, and the particles smaller than the sieve hole size in the crushed material are discharged through the sieve plate. The materials larger than the sieve hole size are retained on the sieve plate and continue to be hit and ground by the hammer until they are crushed to the required discharge particle size and finally discharged outside the machine through the sieve plate.【详情】
锤式粉碎机 pc-350x200
- 类型：塑料粉（破）碎机
- 价格：4000元/台元
- 设备说明：锤式破碎机_重型锤式破碎机_锤式破碎机型号_小型锤式破碎机==河南瑞朗机械
锤式破碎机主要用于破碎一般的脆性矿石，如石灰石、煤、泥质粉砂岩、页岩、石膏等，此系列破碎机是水泥生产专用破碎机，适合破碎石灰石(泥灰岩)和粘土质混合料，还可用于煤块破碎。
锤式破碎机适用于破碎抗压强度<150MPa的石灰石、泥灰岩、砂岩、页岩、石膏、煤等原料，该破碎机可以将采场的大块矿石一次破碎到入磨需要的粒度，从而可以取代传统的两段破碎，简化工艺流程、节约基建投资和生产费用。
主要用于破碎一般的脆性矿石，如石灰石、泥质粉砂岩、页岩、石膏和煤等，此系列破碎机是水泥生产专用破碎机，同时也适合破碎石灰石(泥灰岩)和粘土质混合料。由于破碎机转子尺寸设计合理，机身适当，使得配套设备如吊车、板喂机的选型规格较小，从而节省整个系统的设备投资和基建投资。因此，只要矿石的物理性质合适，选用锤式破碎机作为大型矿山的破碎设备是比较经济可靠的方案。
此破碎机具有入料粒度大，破碎比大的特点，可将大块原矿石一次破碎到符合入磨的粒度，使过去需要的多段破碎的生产系统简化为一段破碎，与传统的两段破碎系统相比，可节省一次性投资45%，车间设备重量减轻32.5%，矿石破碎成本降低40%。操作简单、维修方便、改善了工人的劳动强度，因此，只要矿石的物理性质适合，选用本机做为大型矿山的破矿设备是比较经济可靠的方案。
锤式破碎机作为水泥厂主要原料的破碎设备，与单转子单段破碎设备相比，更适合降雨量较多、料湿、含土较大的工作状况，由于它具有特殊的结构，使得破碎较粘物料时消除了堵塞粘附之患，并且具有特殊的双重过铁保护装置，可将不慎混入机内的铲齿、钻头、铁锤等金属异物自动反弹回给料辊或排出机外，不必为此停机。与相同生产能力的单转子单段锤式破碎机相比，设备重量较轻。由于两个转子可以悬挂更多锤头，所以可供使用的磨损金属量更大，锤头寿命更长。
Hammer crusher, heavy-duty hammer crusher, hammer crusher model, small hammer crusher==Henan Ruilang Machinery
Hammer crushers are mainly used to crush general brittle ores such as limestone, coal, argillaceous sandstone, shale, gypsum, etc. This series of crushers is a specialized crusher for cement production, suitable for crushing limestone (mudstone) and clay mixtures, and can also be used for coal block crushing.
The hammer crusher is suitable for crushing raw materials such as limestone, mudstone, sandstone, shale, gypsum, coal, etc. with compressive strength<150MPa. This crusher can crush large ore blocks from the mining site to the required particle size for grinding in one go, replacing traditional two-stage crushing, simplifying the process flow, saving infrastructure investment and production costs.
Mainly used for crushing general brittle ores such as limestone, argillaceous sandstone, shale, gypsum, and coal, this series of crushers is a specialized crusher for cement production, and is also suitable for crushing limestone (mudstone) and clay mixtures. Due to the reasonable design of the crusher rotor size and appropriate body, the selection specifications of supporting equipment such as cranes and plate feeders are relatively small, thereby saving the equipment investment and infrastructure investment of the entire system. Therefore, as long as the physical properties of the ore are suitable, choosing a hammer crusher as the crushing equipment for large-scale mines is a relatively economical and reliable solution.
This crusher has the characteristics of large feed particle size and high crushing ratio. It can crush large pieces of raw ore to the appropriate particle size for grinding at once, simplifying the production system that used to require multi-stage crushing into one stage crushing. Compared with the traditional two-stage crushing system, it can save 45% of one-time investment, reduce workshop equipment weight by 32.5%, and reduce ore crushing costs by 40%. The operation is simple, maintenance is convenient, and the labor intensity of workers is improved. Therefore, as long as the physical properties of the ore are suitable, using this machine as a crushing equipment for large-scale mines is a relatively economical and reliable solution.
As the main raw material crushing equipment in cement plants, the hammer crusher is more suitable for working conditions with high rainfall, wet materials, and high soil content compared to single rotor single-stage crushing equipment. Due to its special structure, it eliminates the risk of blockage and adhesion when crushing sticky materials. It also has a special double iron protection device, which can automatically bounce back metal foreign objects such as shovel teeth, drill bits, and hammers that accidentally mix into the machine to the feeding roller or discharge outside the machine without stopping the machine. Compared with single rotor single-stage hammer crushers with the same production capacity, the equipment is lighter in weight. Due to the fact that two rotors can suspend more hammer heads, there is a greater amount of wear metal available for use, resulting in a longer lifespan of the hammer heads.【详情】
693